Understanding Tradition
Mastering Innovation

CONCEPT
TAPERED WEDGE
FEMORAL STEM

The concept of tapered wedge femoral stems has been shown to provide excellent implant stability in short term, mid term and long term clinical studies.[1,2,3]

The MasterLoc Hip System follows this philosophy, presenting a novel proximal coating - Mectagrip, designed for initial stability and long term fixation. With an optimized design, the MasterLoc Hip System is suitable for all MIS procedures, especially the AMIS approach.

Progressive triple offset

The MasterLoc Hip System offers a unique progressive triple offset, which allows for an easier and more effective management of the patient’s femoral offset, completely independent from the leg length. This MasterLoc Hip System distinctive offer helps achieving good restoration of the hip joint biomechanics in nearly all patient populations.

Mectagrip coating

A coating treatment consisting of a layer of commercially pure titanium, deposited through Vacuum Plasma Spray technique (VPS). This method offers a high friction coefficient for enhanced initial stability[4], and long term fixation [5,6,7,8] thanks to an optimized porosity: open pores with high porosity level, pore dimensions between 100-350μm, and a continuous interconnectivity.

AMIS friendly design

The MasterLoc Hip System is designed to accommodate all MIS techniques. The instruments and implants have been specifically designed to reduce the risk of damaging soft tissues when utilizing MIS procedures, in particular the AMIS approach.

Simple and reproducible broach only technique

Tapered wedge design with a distally reduced shape

This design philosophy seeks to allow the implant to self-seat within the femoral canal, achieving enhanced mediolateral stability. Applying modern advancements to promote bone preservation, MasterLoc Hip System features a reduced distal geometry and stem length. These features have been introduced to enhance implant fit in the metaphysis while also enhancing performance in Dorr type A, B and C femoral canals. These advances may help prevent unexpected distal fixation and other fit issues demonstrated by early flat, tapered wedge hip systems.[9]


 

 

PRODUCT RANGE

The MasterLoc femoral stem is available in:

  • 12 STANDARD sizes, with 135° neck-shaft angle
  • 14 LATERALIZED sizes, with 127° neck-shaft angle
  • 11 LATERALIZED PLUS sizes, with 122° neck-shaft angle

The lateralized version adds 6 mm of femoral offset and the lateralized plus version adds an additional 5 mm, for 11 mm in total offset, always maintaining the same leg length.

TECHNICAL DATA

TITANIUM ALLOY
The MasterLoc Hip System is manufactured from an industry standard titanium alloy (Ti-6Al-7Nb, in accordance with ISO 5832-11). This material has been shown to have great flexibility and to be highly biocompatible[10].


MECTAGRIP COATING
One of the key features of the MasterLoc Hip System is the use of Medacta’s Mectagrip coating.

Mectagrip is Medacta’s plasma sprayed titanium coating designed to enhance initial stability due to its high coefficient of friction and potential long-term fixation inherent to titanium plasma sprayed devices[11]. Plasma spray coating is one of the most clinically proven surfaces to achieve sound fixation in cementless total hip arthroplasty. Since its introduction in the 1980s, it has become one of the gold standards in cementless fixation[12].
Mectagrip consists of a layer of commercially pure titanium deposited through a special Vacuum Plasma Spray technique (VPS). The VPS method used to deposit the titanium coating on the implant shows potential advantages:

  • Pure titanium composition for optimal biocompatibility;
  • High friction coefficient increasing grip at the interface with bone[4];
  • Favourable environment for bone [5,6,7,8]:
    • open pores with pore dimensions between 100-350 μm;
    • continuous interconnected pores.

TAPERED WEDGE DESIGN WITH A REDUCED DISTAL GEOMETRY

The design concepts of the MasterLoc Hip System adhere to the original design presented by M. E. Müller.

TAPERED WEDGE DESIGN
The stem utilizes a 3-degree taper in the A/P plane, to enhance metaphyseal fixation from the medial aspect of the femur to the lateral aspect of the femoral canal. The transition from the metaphyseal filling region to the smaller diaphyseal region maximizes fixation proximally, reducing the potential of distal fixation.
Wolff’s Law states that bone density will increase under load[13]. Therefore, the stem was designed to enhance proximal load transfer and maintain a good trophic bone in the metaphyseal region.

REDUCED DISTAL GEOMETRY
Studies reported a non negligible incidence of thigh pain related to the first generation of tapered wedge design stems. This was attributed to an unexpected distal fixation observed in some patients’ anatomies (mainly Dorr type A femurs)[14], and it was addressed by the second generation of tapered wedge design stems by reducing the distal shape[15].
The MasterLoc Hip System features a reduced distal geometry, which will enhance the metaphyseal proximal fill, and also make it suitable for Dorr type A femurs, while at the same time allowing for bone preservation.

MIRROR POLISHED NECK WITH REDUCED A/P GEOMETRY

The mirror polished surface of the neck minimizes soft tissue damage and liner wear, making the MasterLoc Hip System
suitable for double mobility liners. Additionally, the reduced A/P geometry may increase the range of motion.

INSTRUMENTATION
  • Dedicated AMIS instrumentation.
  • Both standard and lateralized trial necks fit onto the broaches for a quick and precise trial reduction.
  • Offset broach handles available.
  • High quality sharp broaches for a precise preparation of the medullary cavity.
  • Instruments for calcar preparation included on the ancillary.


AMIS SYNERGY

REDEFINING THR: THE AMIS SYNERGY

The anterior approach, consolidated by years of clinical experience, is the only technique that follows an intermuscular and internervous path and therefore lowers the risk of damaging periarticular structures such as muscles, tendons, vessels and nerves.
The AMIS approach, developed in 2004 by an international group of expert surgeons with the support of Medacta, was born to optimize and enhance the reproducibility of the anterior approach, minimizing soft tissue damage.

With more than 10 years of clinical experience, Medacta International became the world leader for educating and supporting surgeons in their pursuit of Anterior Minimally Invasive Surgery (AMIS). Reference Centers around the world provide the necessary AMIS educational experience and Medacta offers continuous support for surgeons, as well as constantly improving and developing the industry’s most specialized instrumentation platform.

When you use the MasterLoc Hip System, you enter the Medacta International’s world of AMIS.

Discover:

  • The definitive MIS approach: AMIS
  • Dedicated AMIS instrumentation
  • The AMIS Mobile Leg Positioner: the original extension table included as part of the instrumentation, wich makes surgery easier and reproducible
  • The AMIS Education Program based on Medacta’s proven educational process
     

The AMIS Mobile Leg Positioner will be supplied as part of the instrumentation to help ensure effective and reliable positioning of the leg during surgery. Traction, adduction and hyperextension have never been so easy.
 

PUBLICATIONS

[1] Healy W, Tilzey J, Lorio R, Specht L, Sharma S. Prospective, Randomized Comparison of Cobalt-Chrome and Titanium Trilock Femoral Stems. J Arthroplasty. 2009;24:831-6.

[2] Parvizi J, Keisu K, Hozack W, Sharkey P, Rothman R. Primary total hip arthroplasty with an uncemented femoral component: a long-term study of the Taperloc stem. J Arthroplasty. 2004 Feb;19(2):151-6.

[3] McLaughlin J, Lee K. Total hip arthroplasty with an uncemented tapered femoral component. J Bone Joint Surg Am. 2008 Jun;90(6):1290-6.

[4] Friction testing of the Mpact and Versafitcup coating samples. Data on file Medacta.

[5] P. Robotti, A. Sabbioni, L. Glass, B. George, Macroporous Titanium Coatings , by Thermal Plasma Spray, ITSC 2013, International Thermal Spray Conference, May 13 –15, 2013,Busan, Korea.

[6] J. E. Biemond et al, In vivo Assessment of Bone Ingrowth Potential of 3-Dimensional E-Beam Produced Implant Surfaces and the Effect of Additional Treatments by Acid-Etching and Hydroxyapatite Coating, J. Biomat. Appl, published on line January 27, 2011, 0885328210391495.

[7] De Godoy RF, Blunn G, Coathlup ML, Goodship AE. In vivo Evaluation of Titanium Macro-Porous Structures Manufactured Through an Innovative Powder Metallurgy Approach. Proceedings eCM XIII: Bone Fixation, Repair & Regeneration, June 24–26, 2012, Davos, Switzerland.

[8] Goodshi A, Blunn G, Preve E, Facchini L, Bucciotti F, Robotti P. In-vivo Assessment of the Ingrowth Potential of Engineered Surface Topographies Produced by Spark Plasma Sintering. Proceedings 9th World Biomaterial Congress, June 1-5, 2012, Chengdu, China.

[9] McLaughlin JR, Lee KR. Cementless total hip replacement using second-generation components: a 12- to 16-year follow-up. J Bone Joint Surg Br. 2010 Dec;92(12):1636-41.

[10] Khan W, Muntimadugu E, Jaffe M, Domb AJ (2014). Implantable Medical Devices In W Khan and AJ Domb, Focal Controlled Drug Delivery (p. 33-59). Springer New York Heidelberg Dordrecht London.

[11] Khanuja HS, Vakil JJ, Goddard MS, Mont MA. Cementless Femoral Fixation in Total Hip Arthroplasty. J Bone Joint Surg Am. 2011;93:500-9.

[12] Lombardi AV. Porous, plasma-sprayed, titanium-tapered cementless stems achieve versatility. Orthopedics Today, June 2006.

[13] Wolff J. Das Gesetz der Transformation der Knochen. A Hirschwald, Berlin, 1982.

[14] Cooper H, Jacob A, Rodriguez J. Distal Fixation of Proximally Coated Tapered Stems May Predispose to a Failure of Osteointgration. J Arthroplasty. 2011;26:78-83.

[15] McLaughlin JR, Lee KR. Cementless total hip replacement using second-generation components: a 12- to 16-year follow-up. J Bone Joint Surg Br. 2010 Dec;92(12):1636-41.